Parker rotary shaft seals retain lubrication and exclude contaminants even in the most extreme environments. 2 Engineering 2-2P arke H nif C opo t EPS Division Toll Free: (800) 233-3900

Rotary Seal Design Guide, Catalog EPS 5350 Catalog EPS 5350/USA 1-1P arke H nif C opo t EPS Division Toll Free: (800) 233-3900 www.parkerseals.com 1 Introduction The completeness of Parker’sproduct line allows us to provide the optimal design for any rotating application.

Parker's Rotary Sealing Solutions Program provides the most complete coverage in the industry of shaft seals for rotating applications, for both OEM and MRO 

Rotary Seal 4 Busak+Shamban Edition March 2004 GAMMA seals, Axial shaft seals SSeal l IInstallation ll i TTechnical data* h i l d * Family Profile Page B+S type STEFA type Standard (Characteristics) Size range mm Speed m/s Pressure MPa max. GAMMA Seals 152 TBP RB GAMMA 152 TBP RB SSeal l 10 225 20 With t standard 10 - 225 20 ithout 152 TBR 9RB

PS-SEAL PTFE Rotating Shaft Seals give you best-in-class sealing performance for a wide range of high-speed and extreme pressure conditions.

For all rotary seals — FlexiSeal Rotary, FlexiLip and. FlexiCase — the designer must consider: • pressure and shaft velocity. • lubrication.

Rotary Shaft Seals A ADL ADLP AO AODL B BDL BO C CDL BODL CO CODL A Type A Single Lip - Rubber Coated w/ Spring Rubber covered O.D. improves sealing ability at the housing, and is kind to softer materials. The "A" and "ADL" styles will hold up in low-pressure applications. The "AO" and "AODL" are for non-pressure applications only. DIN3760 Standard

The Rotary Shaft Seal is used for excluding dirt, dust, water or other particles, while retaining lubricant in rotary shaft equipment. It was developed as a means of protecting bearings of rotating shafts. The sealing effect is achieved by preloading the sealing lip making its internal diameter slightly smaller than the shaft diameter.

Rotary shaft seals, lip seals and fluid seals that minimize friction and extend service life in high and low speed operation.

Rotary Shaft Seals. 9,789 products. Rotary shaft seals create a seal for rotary elements, such as shafts or rotating bores. They retain bearing lubricant and minimize the entry of dirt, oils, and moisture that would otherwise cause damage and premature failure of bearings and other components. DDS Metric Single Lip with Spring Rotary Shaft Seal.

Rotary seals and shaft seals are used in components with oscillating or rotating parts to keep lubrication fluids in while preventing ingress of mud and water. Trelleborg seals help improve components life and long term performance. Download Trelleborg's Rotary & Shaft Seals Catalogue. Technical Resources Cartridge ROS

As experts in all manner of rotary and shaft seals, MSP offers a diverse range of oil seals and other sealing solutions, including: Grease Seals. Shaft Seals. Mechanical Seals. V-Seals. Braided Packing. We offer both standard and custom configurations for all of our sealing products, with standard and custom sizes measured in inches (SAE, ARP

on a 4.000" shaft rotating at 60 RPM. The lead angle equals 0.0456 = 2' 44.1". A 2" shaft with the same advance (0.300" in 30 seconds at 60 RPM) has a lead angle of 0.0912 = 5' 28.3". For best seal performance, industry standards recommend that the lead

We produce our Bal Seal spring-energized seals for rotary applications in sizes ranging from 0.030 in. (.762 mm) to 120 in. (304.8 cm) inside diameter. Rotary Shaft Seal Service Conditions Temperature, pressure, speed, and media. These are just a few of the major factors you’ll need to consider when choosing a seal for rotary applications.

This catalogue provides a listing of Daemar's standard rotary shaft seal styles and sizes. Accommodating shafts ranging from 1/4” to 40”. The.

Rotary Seals | McMaster-Carr (630) 833-0300 Order History System of Measurement Inch Metric For Shaft Diameter 0.210" to 0.260" 0.217" to 0.256" 1/4" 5/16" 0.370" to 0.450" 0.374" to 0.453" 3/8" 0.450" to 0.530" 0.453" to 0.492" 0.498" to 0.502" 1/2" 0.610" to 0.689" 0.610" to 0.690" 0.623" to 0.627" 5/8" 11/16" 0.690" to 0.770" 0.748" to 0.752"